Check with that product’s set up sheet for instructions. Twist and take away mounting bracket to insert battery. Product Description Lutron’s ceiling-mounted Occupancy Sensors are wireless, battery-powered, passive infrared (PIR) units that robotically control lights via RF communication with a dimming or switching device. These Sensors detect the heat from people transferring within an area to determine when the area is occupied. The Sensors then transmit the suitable commands to the related dimming or switching system to show the lights on or off routinely, offering each convenience and exceptional vitality savings. Sensor doesn't carry out satisfactorily from this location, it could also be moved to 1.Four Ifanother location by pulling the Sensor straight down and repeating steps 1.Three and 1.4. 1.5 If the Sensor’s efficiency is passable, it must be completely connected to the ceiling tile, as described in part G. Permanent Mounting. Temporary Solid Ceiling Mounting Use this procedure if the Sensor can be mounted on a stable, steady ceiling floor similar to drywall, plaster, concrete, or wood. Two 3M™ Command™ adhesive strips are offered for temporarily mounting and testing the Sensor on smooth, solid ceiling surfaces. These strips are designed for easy, damagefree removal and will not be reusable. These strips should not be used for completely mounting the Sensor (see section G. Permanent Mounting ). Carefully follow the removing instructions under to make sure the ceiling is just not damaged during removing. Note: Don't use the adhesive strips on ceiling tiles, as they will likely trigger injury to the tile upon elimination. Simple-to-comply with Directions Set-Up In order for the Sensor to operate correctly, it should first be set up with a corresponding dimming or switching system. The procedure for organising a Sensor with a Maestro Wireless® (MRF2- only) Dimmer or Electronic Switch is detailed under. P/N 041-172a 2.1 Peel the purple "Command Strips" liner off of one of the adhesive strips and apply the strip to the flat facet of the mounting bracket as proven within the diagram. Notice: Don't cover the bracket’s screw holes as a result of they will be used to mark screw gap locations on the ceiling. Organising a Sensor with a Maestro Wireless Dimmer or Electronic Switch Dimmer Key Features · Low Upkeep. 10-year battery life. Handy low-battery indicator. · A number of Units. Up to 3 Sensors can work together to manage lights for broader protection in giant areas. Every Sensor may be added to as much as 10 receiving devices. Sensor Operation Occupancy Model - The Sensor will mechanically turn the lights on when the space is occupied and mechanically flip the lights off after the area is vacated. The Sensor will automatically turn the lights off after the space is vacated. There's a constructed-in 15-second vacancy grace period that begins when the lights are automatically turned off, during which the lights will automatically flip again on in response to movement. This grace period is supplied as a safety and comfort characteristic in the event that the lights turn off while the room remains to be occupied, in order that the user does not have to manually turn the lights back on. After 15 seconds, the grace interval expires and the lights must be manually turned on. This Sensor is a part of a system and cannot be used to control a load with out a appropriate dimming or switching system. Refer to the instruction sheets of the receiving gadget(s) for set up data. The Sensor could also be put in as much as 60 ft (18.3 m) away from the associated dimming or switching device(s) if they're in direct line of sight. If there are walls or different boundaries between the Sensor and receiving machine(s), the Sensor ought to be positioned inside 30 ft (9.1 m). Warning: This product should not be used to control tools which could create hazardous conditions, akin to entrapment, if operated by accident. Sensor in a location where it has a broad view outside the intended space. If that is unavoidable, the lens can be masked to dam the view of undesired areas (confer with section I. Lens Masking). This guarantee is in lieu of all other categorical warranties, and the implied warranty of merchantability is restricted to 1 12 months from purchase. This guarantee does not cowl the price of installation, elimination or reinstallation, or injury ensuing from misuse, abuse, or harm from improper wiring or set up. This warranty does not cowl incidental or consequential damages. LUTRON’S Legal responsibility ON ANY Claim FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, Set up, Supply, OR USE OF THE UNIT SHALL Never EXCEED THE PURCHASE Price OF THE UNIT. This guarantee provides you particular legal rights, and you might have other rights which vary from state to state. Some states do not permit the exclusion or limitation of incidental or consequential damages, or limitation on how lengthy an implied guarantee might final, so the above limitations could not apply to you. Patents pending. Lutron, Maestro Wireless, and the Sunburst brand are registered trademarks and Radio Powr Savr is a trademark of Lutron Electronics Co., Inc. ANSI is a registered trademark of the American National Requirements Institute. IEC is a trademark of the Worldwide Electrotechnical Commission. Made and printed in the U.S.A. 25/09/09 P/N 041-172 Rev. A 8 ft (2.Four m) 18 x 18 ft (5.5 x 5.5 m) thirteen ft (4.0 m) 9 ft (2.7 m) 20 x 20 ft (6.1 x 6.1 m) 14.5 ft (4.Four m) 10 ft (3.0 m) 22 x 22 ft (6.7 x 6.7 m) sixteen ft (4.9 m) 12 ft (3.7 m) 26 x 26 ft (7.9 x 7.9 m) 19 ft (5.8 m) Non permanent Mounting Methods 1.1 1.2 Insert the ceiling tile mounting wire by the 2 smaller holes within the mounting bracket and exchange the mounting bracket. Mount Sensor to a ceiling tile by inserting the wire legs by the tile, making sure the Sensor is flush to the tile. Word: Don't twist wire legs together. 1.2 After the Sensor has been briefly mounted, leave the Sensor in place on the tile and both take the tile down or remove an adjoining tile to achieve entry to the legs of the mounting wire on the again of the tile. Low Activity: This is essentially the most delicate setting and will detect very slight motions. That is the advisable setting, as it would work nicely for almost all purposes. It is right for spaces where occupants will usually be seated for long periods of time. Twist the wire legs collectively tightly so the mounting bracket remains snug towards the tile. This setting is barely much less delicate than the Low Exercise setting and can be utilized for areas that expertise regular activity. That is the least delicate setting and can be used for spaces that may generally only experience large motions, comparable to foot visitors. The Low Exercise setting is the default and can perform finest for most functions. Rarely, if the Sensor is placed near exterior noise sources akin to heating vents, air conditioning vents, or gentle bulbs, it might turn the lights on without occupancy or keep the lights on too long after vacancy. If this happens, altering the sensitivity to Medium Activity or High Activity ought to resolve the issue. Replace the tile. Permanent Solid Ceiling Mounting 2.1 2.2 2.Three Advanced Set-Up Operation The advanced set-up is accessed through the use of the buttons on the again of the Sensor. Drill two 3/16 in (4.6 mm) pilot holes for the supplied screw anchors. Press the anchors into the holes and faucet flush with a hammer. To display the present setting, press and launch the specified button. An LED will illuminate briefly, indicating the present setting. Place the flat aspect of the mounting bracket against the ceiling and install the 2 supplied screws using a hand screwdriver. To adjust a setting, press and hold the desired button till the LED corresponding to the current setting begins flashing quickly, indicating the setting can now be adjusted. Every subsequent button press of lower than 2 seconds will increment the mode to the next out there setting. Urgent any of the other buttons will haven't any effect. To save lots of the chosen setting, press and hold the button until the LED turns on stable, indicating the saved setting. Through the adjustment procedure, if there isn't a exercise for 30 seconds, the LEDs will flip off and no settings will be saved. Notice: Don't over-tighten. 2.Four Attach the Sensor to the mounting bracket by inserting and twisting in a clockwise course till the Sensor locks into place. To take away the bracket from the ceiling, grasp the elimination tab on the adhesive strip and pull the tab VERY SLOWLY straight across the ceiling, stretching the strip until the bracket releases from the ceiling. Discard the strip. Never pull the strip at an angle, as it may break or damage the ceiling surface. Observe: Don't pull at an angle. Lens Masking (Optional) Whenever doable, the Sensor needs to be put in in a location the place it cannot easily see into areas exterior the intended house, corresponding to hallways or adjacent rooms. If this situation can't be prevented, parts of the lens may be masked with the supplied labels to dam the Sensor’s view of the undesired areas. It's endorsed to remove the Sensor from the mounting bracket earlier than applying Superior Set-Up (Optionally available) the masking labels. The Sensor options a number of superior set-up modes. For nearly all of installations, the default settings will provide the perfect efficiency and you won't have to make the most of the superior set-up. The Occupancy version of the Sensor has three adjustable advanced set-up modes: Timeout, Auto-On, and Sensitivity. The Vacancy-Only version has only two modes (Auto-On not out there). The default settings are listed below. The Sensor could be screwed onto the mounting bracket in several different orientations. Make sure to notice the Sensor’s orientation earlier than taking it down and change the Sensor in the identical orientation to ensure the meant space will get blocked. Outer lens sections correspond to the detection areas furthest away from the Sensor, while inner sections correspond to areas closer to the Sensor. Watch out when making use of the labels to avoid creating gaps between adjacent masked sections. The Sensor could detect movement by inadvertent gaps. Always (Occupancy model only) Timeout 30 min 15 min 5 min Auto-On Always Low mild Disable Exercise Timeout 30 min 15 min 5 min Superior Set-Up Modes Auto-On All the time Low mild Disable Exercise Activity: Low Activity Lens sections shown in white are masked with labels Timeout The Sensor will turn the lights off if no motion happens at some point of the timeout interval. There are three available timeout settings: 5, 15, and 30 minutes. Lens Mask Lens sections proven in gray haven't been masked Auto-On The automatic-on performance of the Sensor will be adjusted to manage how the lights reply upon preliminary occupancy. There are three obtainable settings: Always, Low mild, and Disable. Always: The lights will at all times turn on. Testing Sensor Protection With the Sensor mounted on the ceiling, press and launch the "Test: Sensor" button on the front of the gadget. The lens will glow briefly, indicating the test mode has been entered. Be aware: There's a warm-up period of roughly forty seconds after the batteries are installed earlier than the check mode might be activated. If the button is pressed during this time, the lens will flash continuously till the warm-up period is full, after which the check mode will probably be robotically entered. Verify the coverage space by walking via the house and observing the lens. The lens will glow strong every time motion is detected. If the lens stays off throughout motion, the Sensor can not detect movement at that location. Press and release the "Test: Sensor" button again to exit the test mode. If the button just isn't pressed, the take a look at mode will routinely time out quarter-hour after being enabled, or 5 minutes after the final detected movement if the room is vacated. If the Sensor has vital trouble detecting motion in the course of the check, it ought to be moved to a different location and retested. If the Sensor still has poor detection from the brand new location, discuss with the Troubleshooting section. Momentary Drop Ceiling Mounting Use this procedure if the Sensor will likely be mounted on a ceiling tile. The ceiling tile mounting wire is supplied for both momentary and everlasting mounting of the Sensor to drop ceilings composed of a number of tiles. It's designed to allow short-term mounting, testing, and repositioning (if necessary) of the Sensor with out damaging a ceiling tile. As soon as the Sensor’s closing place has been chosen, the mounting wire can be twisted to lock the Sensor in place completely. If the Sensor coverage and wireless communication tests have been efficiently accomplished, use the mounting bracket as a template to mark the screw hole areas with a pencil. Notice: Pull very slowly. Max. Room Dimensions Radius of Coverage for Full Protection at Flooring If you're unsure about accurately positioning the Sensor, the following temporary mounting and testing procedures are really helpful to verify proper performance before permanently putting in the Sensor. Sensor’s detection range relies on the ceiling height, as proven within the table beneath. Discover: Don't disassemble, crush, puncture, or incinerate the batteries. Do not dispose of batteries in normal household waste. Please recycle, take to a proper battery disposal facility, or contact your native waste disposal provider concerning native restrictions on the disposal or recycling of batteries. O NOT mount the Sensor within four ft (1.2 m) of HVAC vents or light bulbs installed under the ceiling line. Hotter rooms might reduce the Sensor’s skill to detect occupants. Use only high-high quality lithium batteries, size CR123, three V (ANSI-5018LC, IEC-CR17345). Don't use rechargeable batteries. Utilizing improperly rated batteries might damage the Sensor. For questions concerning the installation or operation of this product, name the Lutron Technical Help Middle. Please provide exact mannequin quantity when calling. U.S.A. and Canada (24 hrs / 7 days) Setting the Occupancy Mild Level (occupancy version, dimming units only) the Sensor to the mounting bracket by inserting and twisting in a clockwise 2.5 Attach route until the Sensor locks into place. Sensor coverage and wireless communication tests as described in 2.6 Carry out sections E. Testing Sensor Coverage and F. Testing Wireless Communication. The Sensor must be put in in a location the place it has a great view of all elements of the room. The Sensor requires line of sight to operate properly. If you cannot see the Sensor, it can not see you. The Sensor cannot see through glass objects resembling patio or shower doors. The vary and efficiency of the RF system is very dependent on quite a lot of advanced elements similar to: · Distance between system elements · Geometry of the building construction · Construction of walls separating system parts · Electrical gear positioned close to system components Technical Help 2.2 Determine a location on the ceiling where the Sensor can have an excellent view of the room. 2.3 Take away the black "wall side" liner from the adhesive strip. The Sensor is designed for ceiling use only. Do not install on ceilings larger than 12 ft (3.7 m) or non-ceiling surfaces. Doing so may significantly inhibit the Sensor’s efficiency. 4. Don't paint Sensor. · · · · The "Lights On" and "Lights Off" buttons should now swap the lights within the room on and off, respectively, when pressed. Repeat the above procedure to arrange the Sensor with any extra units. The Sensor is meant for indoor use solely. Function between 32 °F and 104 °F (zero °C and forty °C). 1.1 several seconds. Sensor that has been arrange. After roughly 6 seconds, the lens will flash rapidly several instances, indicating the sunshine level has been saved. All Sensors set up with the Dimmer will now use the saved occupancy mild level. 2. Clear Sensor with a comfortable damp cloth solely. Do not use any chemical cleaners. Word: This gear has been examined and found to comply with the boundaries for a category B digital device, pursuant to half 15 of the FCC guidelines. These limits are designed to offer affordable protection against harmful interference in a residential set up. This gear generates, uses and may radiate radio frequency energy and, if not put in and utilized in accordance with the directions, may cause dangerous interference to radio and tv reception, which might be decided by turning the tools off and on. The person is inspired to attempt to correct the interference by a number of of the next measures: Reorient or relocate the receiving antenna. Improve the separation between the gear and receiver. Connect the gear into an outlet on a circuit completely different from that to which the receiver is connected. Seek the advice of the seller or an skilled radio/Tv technician for assist. Caution: Changes or modifications not expressly authorized by Lutron Electronics Co. could void the user’s authority to operate this gear. This machine complies with Part 15 of the FCC guidelines. This machine should settle for any interference received, including interference that may cause undesired operation. Swap 2.1 Set the Dimmer to the desired light degree for getting into the room. 2.2 Save holding the "Lights On" button on the entrance of a Be aware: For either Sensor version, the lights can also be manually turned off at any time through the use of the dimming or switching system instantly. Vital Notes or Add the Sensor to the Dimmer or Change by pressing and holding the "Lights Off" button on the entrance of the Sensor for roughly 6 seconds until the lens flashes briefly. The lights in the room will even flash three instances, indicating the Sensor has been efficiently added. The Dimmer or Change will exit set-up mode routinely. The sensitivity of the Sensor might be adjusted primarily based on the anticipated stage of activity within the room. There are three accessible exercise settings: Low Activity, Medium Activity, and High Exercise. Permanent Drop Ceiling Mounting Observe: Depart the removal tab uncovered previous the edge of the bracket so it may be accessed for elimination later. 6 seconds until all LEDs on the device start flashing. Release the faucet button. Sensor is detecting motion in areas that are not desirable, equivalent to hallways or adjoining rooms, seek advice from section I. Lens Masking. If Sensor detection is satisfactory during this check, carry out the wireless communication test as described in section F. Testing Wireless Communication. Testing Wireless Communication This check should be performed to verify that the Sensor has been appropriately set up with the corresponding dimming or switching gadget and that there is correct wireless communication from the chosen Sensor location. If the lights within the room are not on, turn them ON manually on the dimming or switching system. Press and launch the "Lights Off" button on the entrance of the Sensor. The lights ought to flip OFF. Press and launch the "Lights On" button on the front of the Sensor. The lights should activate. If the lights don't reply appropriately, seek advice from the Troubleshooting section. Low mild: The lights will only activate routinely upon entry if there is not already enough ambient gentle in the room. Hallway falls within Sensor’s coverage space. Disable: This setting converts the Sensor to vacancy mode. The lights won't robotically activate but will still automatically flip off after vacancy. The lights have to be manually turned on by using the associated dimming or switching gadget. Word: The 15-second vacancy grace period is lively in this mode. Discuss with the Sensor Operation section at first of this doc for more particulars. Troubleshooting Symptom Doable Causes Resolution Lights don't activate when space is occupied. Sensor isn't accurately added to dimming / switching machine(s). Sensor’s Auto-On setting is ready to "Low light" or "Disable". The lights have been lately turned off manually and the timeout has not but expired. Sensor doesn't have full view of room. Sensor is exterior wireless vary of dimming/switching gadget. Confer with section B. Set-Up. Seek advice from part H. Superior Set-Up. Dimming/switching gadget has been improperly wired. Gentle bulb(s) burned out. Breaker is off or tripped. Sensor’s timeout is too brief for this utility. Sensor doesn't have full view of room. Lens mask is improperly utilized. Sensor’s sensitivity is too low. Sensor’s timeout has not yet expired. An external noise supply comparable to an HVAC vent is interfering. Consult with section A. Pre-Installation. Conduct of lights does not match Sensor settings. Sensor coverage extends beyond room perimeter. The supposed setting was not saved. A number of Sensors are added to a dimming/switching gadget and their settings do not match. Consult with section A. Pre-Set up. Check with part C. Sensor Placement or I. Lens Masking. Seek advice from part H. Superior Set-Up. Discuss with part H. Advanced Set-Up. Sensor lens doesn't glow in response to motion during Sensor protection testing. Sensor can not see movement due to obstruction. Room is simply too large or oddly shaped. Transfer Sensor to another location. Seek advice from part C. Sensor Placement. A number of Sensors may be necessary for full room coverage. Try shifting Sensor to a brand new location or reducing sensitivity. Confer with part C. Sensor Placement or H. Superior Set-Up. Lights turn OFF whereas house is occupied. Lights keep ON after area is vacated. Lens does not stop glowing throughout Sensor coverage testing even when there is no movement. Lights do not respond accurately during wireless communication testing. Sensor lens flashes and lights do not activate when area is occupied. Battery has been put in incorrectly. An external noise source equivalent to an HVAC vent is interfering. Check with part C. Sensor Placement. Seek advice from part C. Sensor Placement or F. Testing Wireless Communication. Consult with section H. Advanced Set-Up. Seek advice from part C. Sensor Placement. Confer with part I. Lens Masking. Seek advice from section H. Superior Set-Up. Seek advice from section H. Advanced Set-Up. Attempt moving Sensor to a brand new location or reducing sensitivity. Discuss with part C. Sensor Placement or H. Superior Set-Up. Sensor just isn't correctly added to dimming / switching gadget. Sensor is outside wireless range of dimming/switching system. Confer with section B. Set-Up. Transfer Sensor closer to dimming/switching machine and retry test. Consult with part F. Testing Wireless Communication. Battery has been put in incorrectly. Dimming/switching device has been improperly wired. Gentle bulb(s) burned out. Breaker is off or tripped. Battery is low. Consult with part A. Pre-Installation. Take away sensor from check mode. Discuss with part E. Testing Sensor Protection.
Check out my blog post ... junecourt73.bravejournal.net